Single Wire Series - SMC - Antenna and Mast Specialists

Frequency Range: 2-3MHz
Bandwidth: +/- 2% of centre frequency
Power Rating: 1kW
SWR: Better than 1.5:1
Impedence: 50 Ohm
Polarisation: Horizontal
Antenna Elements: Stainless steel stranded wire 1×19 3mm
Antenna Configuration: Horizontal
Footprint: Dependent on frequency
Mast Requirements: Two required
Input Connector: N Type
Cable: UR67 x 30m

Add to Quote

CFD1ATA100UP

Frequency Range: 3-30MHz
Bandwidth: +/- 2% of centre frequency
Power Rating: 1kW
SWR: Better than 1.5:1
Impedence: 50 Ohm
Polarisation: Horizontal
Antenna Elements: Copper wire hard drawn stranded 7×0.92mm
Antenna Configuration: Horizontal
Footprint: Dependent on frequency
Mast Requirements: Two required
Input Connector: N Type
Cable: UR67 x 30m

Add to Quote

CFD1ATA15DN

Frequency Range: 2-3MHz
Bandwidth: +/- 2% of centre frequency
Power Rating: 150W
SWR: Better than 1.5:1
Impedence: 50 Ohm
Polarisation: Horizontal
Antenna Elements: Copper wire hard drawn stranded 7×0.92mm
Antenna Configuration: Horizontal
Footprint: Dependent on frequency
Mast Requirements: Two required
Input Connector: SO239
Cable: UR67 x 30m

Add to Quote

CFD1ATA15UP

Frequency Range: 2-30MHz
Bandwidth: +/- 2% of centre frequency
Power Rating: 150W
SWR: Better than 1.5:1
Impedence: 50 Ohm
Polarisation: Horizontal
Antenna Elements: Copper wire hard drawn stranded 7×0.92mm
Antenna Configuration: Horizontal
Footprint: Dependent on frequency
Mast Requirements: Two required
Input Connector: SO239
Cable: UR67 x 30m

Add to Quote

FM5

Height Extended (m): 4.7

Height Retracted (m): 1.63

Number of Sections: 5

Weight (kg): 25

Vertical Head Load (kg): 45

Add to Quote

FM6

Height Extended (m): 6.6

Height Retracted (m): 2.02

Number of Sections: 5

Weight (kg): 29

Vertical Head Load (kg): 36

Add to Quote

FM8

Height Extended (m): 8

Height Retracted (m): 2.31

Number of Sections: 5

Weight (kg): 33

Vertical Head Load (kg): 28

Add to Quote

FWB 2530

Frequency Range: 2.5 – 30MHz

Gain: >3 dBi

Impedance: 50 ohm unbalanced

Polar Diagram ‘H’ Plane: Generally omnidirectional

Polar Diagram ‘E’ Plane: 30 – 90

Power: Rx – 1kW AVE

VSWR: 3 : 1 max, 2.1 : 1 AVE

Add to Quote

FWB 2530/1KW/PA

Frequency Range: 2.5 – 30MHz

Bandwidth: Wideband

Power Rating: 1kW

SWR: 2.5:1

Polarisation: Horizontal

Antenna Elements: Copper wire hard drawn stranded

Antenna Configuration: Inverted V

Footprint: 48m x 2.5m

Mast Requirements: Single 18m

Input Connector: N Type

Cable: UR67 x 20m

Add to Quote

FWB 2530/400

Frequency Range: 2.5 – 30MHz

Bandwidth: Wideband

Power Rating: 400W

SWR: 2.5:1

Polarisation: Horizontal

Antenna Elements: Copper wire hard drawn stranded

Antenna Configuration: Inverted V

Footprint: 48m x 2.5m

Mast Requirements: Single 18m

Input Connector: N Type – No mast included

Cable: UR67 x 20m

Add to Quote

FWB 2530/400/PA

Frequency Range: 2.5 – 30MHz

Bandwidth: Wideband

Power Rating: 400W

SWR: 2.5:1

Polarisation: Horizontal

Antenna Elements: Copper wire hard drawn stranded

Antenna Configuration: Inverted V

Footprint: 48m x 2.5m

Mast Requirements: Single 18m

Input Connector: N Type

Cable: UR67 x 20m

Add to Quote

GRP20/SYS

Height Extended (m): 6.1

Height Retracted (m): 1.7

Number of Sections: 4

Weight (kg): 3kg

Add to Quote

GRP30/SYS

Height Extended (m): 9.25

Height Retracted (m): 2.35

Number of Sections: 5

Weight (kg): 6kg

Add to Quote

HD9-12L

Height Extended (m): 12.1

Height Retracted (m): 2.5

Number of Sections: 8

Vertical Head Load (kg): 264

Add to Quote

HD9-18L

Height Extended (m): 18.1

Height Retracted (m): 2.7

Number of Sections: 12

Vertical Head Load (kg): 90

Add to Quote

HD9-24L

Height Extended (m): 24.1

Height Retracted (m): 4.4

Number of Sections: 7

Vertical Head Load (kg): 90

Add to Quote

HD9-31L

Height Extended (m): 30.9

Height Retracted (m): 4.5

Number of Sections: 9

Vertical Head Load (kg): 40

Add to Quote

HD9-4L

Height Extended (m): 4.4

Height Retracted (m): 1.6

Number of Sections: 5

Vertical Head Load (kg): 420

Add to Quote

HF10 Series – 1 kW HF Wide Band Antenna Matching

Balance Ratio: >26 dB

Balance Terminals: Alumina ceramic M10 thread

Coaxial Connectors: ‘N’ type (others on request)

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain (NB No internal capacitors fitted.)

Impedance: See table below

Insertion Loss: <0.3 dB

Load VSWR: 2.5 : 1 max

Power: 1kW average, 4kW peak

Shipping Dimensions: 0.425m x 0.3m x 0.15m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 5kg

Add to Quote

HF100 300/600 High Power Balanced/Balance Matching

Balance Ratio: >26 dB

Balance Terminals: Alumina ceramic M12 thread

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Cooling: Natural convection, silicone transformer oil, pressure relief valve fitted.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing honrs

Input Impedance: 300 ohm balance

Insertion Loss: <0.2 dB

Load VSWR: 2.5 : 1 max

Output Impedance: 200 ohm or 600 ohm balance

Power: 10kW average +100% AM modulation

Shipping Dimensions: 0.7cm x 0.6m x 0.5m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 60kg gross

Add to Quote

HF100 Series – 10 kW HF Wide Band Antenna Matching

Balance Ratio: >26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 7/8″, 1 5/8″, 3 1/8″ EIA

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Cooling: Natural convection, silicone transformer oil, pressure relief valve fitted.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain

Impedance: See table below

Insertion Loss: <0.2 dB

Load VSWR: 2.5 : 1 max

Power: 10kW average

Shipping Dimensions: 0.7m x 0.6m x 0.5m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 60kg

Add to Quote

HF200 Series – 20 kW HF Wide Band Antenna Matching

Balance Ratio: > 26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 1 5/8″, 3 1/8″ EIA

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain

Impedance: See table below

Insertion Loss: <0.2 dB

Load VSWR: 2.5 : 1 max

Power: 20kW average

Shipping Dimensions: 0.7m x 0.6m x 0.5m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 110kg

Add to Quote

HF30 Series – 3 kW HF Wide Band Antenna Matching

Balance Ratio: >26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 7/8″ EIA (others on request)

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain (NB No internal capacitors fitted.)

Impedance: See table below

Insertion Loss: <0.3 dB

Load VSWR: 2.5 : 1 max

Power: 3kW average, 12kW peak

Shipping Dimensions: 0.32m x 0.30m x 0.14m

Temperature Range: -35°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 14kg

Add to Quote

HF300 Series – 30 kW HF Wide Band Antenna Matching

Balance Ratio: >26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 3 1/8″ EIA

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain

Impedance: See table below

Insertion Loss: <0.2 dB

Load VSWR: 2.5 : 1 max

Power: 30kW average

Shipping Dimensions: 1m x 0.7m x 0.55m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 120kg

Add to Quote

HF4 Series 400 Watt HF Wide Band Antenna Matching

Balance Ratio: > 26 dB

Balance Terminals: Alumina ceramic M6 thread

Coaxial Connectors: ‘N’ type (others on request)

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain (NB No internal capacitors fitted.)

Impedance: See table below

Insertion Loss: <0.3 dB

Load VSWR: 2.5 : 1 max

Power: 400 Watt average, 1600 Watt peak

Shipping Dimensions: 0.22m x 0.15m x 0.12m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 1.2kg

Add to Quote

HF50 Series – 5 kW HF Wide Band Antenna Matching

Balance Ratio: > 26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 7/8″ EIA (others on request)

Configuration: Cast aluminium case (LM25). Hermetically sealed. Epoxy paint finish.

Frequency: 1.5 – 32MHz

High Voltage Protection: Arcing horns and internal static drain

Impedance: See table below

Insertion Loss: <0.3 dB

Load VSWR: 2.5 : 1 max

Power: 5kW average, 20kW peak

Shipping Dimensions: 0.49m x 0.41m x 0.39m

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1 (2 – 30MHz), <1.3 : 1 (1.5 – 32MHz)

Weight: 38kg

Add to Quote

HF500/1000 High Power Broadcast Antenna Matching

Balance Ratio: > 26 dB

Balance Terminals: P.T.F.E. M10 thread

Coaxial Connectors: 3 1/8″ and 6 1/8″ EIA

Configuration: Aluminium tank, silicone oil cooled, pressure relief valve fitted

Frequency: 3 – 22MHZ

High Voltage Protection: Arcing horns and internal static drain

Input Impedance: 50 ohm unbalance

Insertion Loss: <0.1 dB

Load VSWR: 2.5 : 1 max

Output Impedance: 200 ohm or 600 ohm balance

Power: HF500 – 50kW average. HF1000 – 100kW average.

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1

Weight: 450kg

Add to Quote

HFC1-30 – 1kW HF Directional Coupler

Connectors: Main line ‘N’ Female. Coupled line ‘BNC’ Female

Coupling Ratio: -30 dB +/- 0.5 dB

Forward/Reverse Discrimination: >30 dB

Frequency: 2 – 50MHz Full specification*

Insertion Loss: <0.1 dB

Max VSWR: 2.5: 1

Power Rating: 1kW continuous. 2.5kW peak

Return Loss (Matched Load): 26.5 dB

Add to Quote

HFC10-26 – 10kW HF Directional Coupler

The coupler uses ferrite transformer techniques resulting in an extremely small compact device for permanent installation or for field measurement purposes.

Output samples of forward and reverse power flow are provided. Being effectively a “dual” coupler the reverse signal is largely independent of the load on the forward port (and vice versa). Built in load resistors dissipate any un-terminated coupled power.

Connectors: Main line 1 7/8″. Coupled line – ‘N’ female

Coupling Ratio: -26 dB +/- 0.5 dB

Forward/Reverse Discrimination: >30 dB

Frequency: 2 – 32MHz Full specification*

Insertion Loss: <0.1 dB

Max VSWR: 2.5: 1

Notes: At 30kW the forward output signal is 75 Watt. *The coupler is effective over a very much wider frequency range with a small degradation in performance. Calibration charts can be supplied for those out of band frequencies, where for example, measurement of harmonics is desired.

Power Rating: 30kW continuous and peak

Return Loss (Matched Load): 26.5 dB

Add to Quote

HFC30-26 – 30kW HF Directional Coupler

The coupler uses ferrite transformer techniques resulting in an extremely small compact device for permanent installation or on field measurement purposes.

Connectors: Main line 1 5/8″. Coupled line – ‘N’ female

Coupling Ratio: -26 dB +/- 0.5 dB

Forward/Reverse Discrimination: >30 dB

Frequency: 2 – 32MHz Full specification*

Insertion Loss: <0.1 dB

Max VSWR: 2.5: 1

Power Rating: 30kW continuous and peak

Return Loss (Matched Load): 26.5 dB

Add to Quote

HFH2-1 – 2 x 1kW HF Broad Band Hybrid Combiner

Connectors: ‘N’

Construction: Cast aluminium case, solid encapsulation, epoxy paint finish

Environment: Outdoor unprotected

Frequency: 1.5 – 32MHz

Impedance: 50 ohm

Input Power: 2 x 1kW average (2kW peak)

Insertion Loss: <0.25 dB (matched loads)

Isolation: >30 dB (matched loads)

Load Ports: 2 x 50 ohm ‘N’ Connectors

Load VSWR: 2.5 : 1 max

Output Power: 2kW average (4kW peak)

Temperature: -40°C to +70°C

VSWR: <1.2 : 1 max

Weight: 12kg

Add to Quote

HFH2-10 – 2 x 10kW HF Broad Band Hybrid Combiner

Connectors: 7/8″ or 1 5/8″ EIA

Construction: Aluminium case, silicon oil cooled, pressure relief valve, epoxy paint finish

Frequency: 2 – 30MHz

Impedance: 50 ohm

Insertion Loss: <0.25 dB (matched loads)

Isolation: >30 dB (matched loads)

Load Ports: 2 x 50 ohm 7/8″ EIA

Load VSWR: 2.5 : 1 max

Power: 2 input channels, each 10kW average (40kW peak), 20kW average output for co-phased inputs

Temperature: -40°C to +70°C

VSWR: <1.2 : 1 max

Weight: 55kg

Add to Quote

HFH2-2 – 2 x 2 kW HF Broad Band Hybrid Combiner

Connectors: ‘N’, ‘HN’

Construction: Cast aluminum case, solid encapsulation, epoxy pain finish

Environment: Outdoor unprotected

Frequency: 1.5 – 31MHz

Impedance: 50 ohm

Input Power: 2 x 2kW average (4kW peak)

Insertion Loss: <0.25 dB (matched loads)

Isolation: >30 dB (matched loads)

Load Ports: 2 x 50 ohm ‘N’ Connectors

Load VSWR: 2.5 : 1 max

Output Power: 4kW average (8kW peak)

Temperature: -40°C to +70°C

VSWR: <1.2 : 1 max

Weight: 12kg

Add to Quote

HFH4-1 – 4 x 1 kW HF Broad Band Hybrid Combiner

Balancing Loads: 6 x 500 Watt 50 ohm

Cooling: Solid encapsulation natural convection

Frequency: 2 – 40MHz

Impedance: 50 ohm

Input Sockets: ‘N’ Sockets

Input Power: 4 x 1kW average

Insertion Loss: 0.5 dB (matched loads)

Isolation: >30 dB (matched loads)

Load Sockets: ‘N’ Sockets

Load VSWR: 3 : 1 max

Output Sockets: ‘N’ Sockets

Phase: 0° +/- 5°

Splitter Loss: 6 dB

Temperature: -40°C to +55°C

VSWR: <1.2 : 1 max

Add to Quote

HFH6-50/B – Broad Band VHF Hybrid Combiner

Configuration: Cast aluminium case, solid encapsulation, epoxy paint finish

Connectors: BNC

Frequency: 20 – 90MHz

Impedance: 50 ohm

Input Power: 6 x 50 Watt

Insertion Loss: <0.75 dB + 7.8 dB splitting loss

Isolation: >40 dB (matched loads)

Load Ports: 8 x 50 ohm (32 Watt each)

Load VSWR: 2.5 : 1 max

Output Power: 50 Watt

VSWR: Less than 1.2 : 1 (matched loads)

Weight: 1kg (exclusive of mounting plate and loads)

Add to Quote

HFM2-1 – 2 x 1 kW HF Transmitter Multicouplers

Connectors: ‘N’, ‘HN’, 7/8″ EIA, 7/16″ Spinner

Cross Cover Frequency: Notch centre to be specified between 3-18MHz (lower notch centres available)

Environment: Indoor -40°C to +55°C (natural convection)

Frequency: 0.1 – 32MHz

Impedance: 50 ohm

Insertion Loss: <0.3 dB (matched load)

Isolation: >30 dB (matched load)

Load VSWR: 3 : 1 max

Notch Width: 15%, 20%, 40% of cross over frequency

Power: 2 input channels each 1kW average (2kW peak) 1 output channel 2kW average (4kW peak)

VSWR: <1.2 : 1 (matched loads)

Weight: 15kg

Add to Quote

HFM2-10 – 2 x 10 kW HF Transmitter Multicouplers

Connectors: 1 5/8″, 3 1/8″ EIA

Cross Cover Frequency: Notch centre to be specified between 3-18MHz (lower notch centres available)

Environment: Outdoor unprotected -40°C to +55°C. Silicone oil cooled natural convection

Frequency: 0.1 – 32MHz

Impedance: 50 ohm

Insertion Loss: <0.3 dB (matched load)

Isolation: >30 dB (matched load)

Load VSWR: 3 : 1 max

Notch Width: 15%, 20%, 40% of cross over frequency

Power: 2 input channels each 20kW average (40kW peak), 1 output channel 40kW average (80kW peak)

VSWR: <1.2 : 1 (matched loads)

Weight: 250kg

Add to Quote

HFM2-2 – 2 x 2 kW HF Transmitter Multicouplers

Connectors: ‘N’, ‘HN’, 7/8″ EIA, 7/16″ Spinner

Cross Cover Frequency: Notch centre to be specified between 3-18MHz (lower notch centres available)

Environment: Indoor -40°C to +55°C (natural convection)

Frequency: 0.1 – 32MHz

Impedance: 50 ohm

Insertion Loss: <0.3 dB (matched load)

Isolation: >30 dB (matched load)

Load VSWR: 3 : 1 max

Notch Width: 15%, 20%, 40% cross over frequency

Power: 2 input channels each 2kW average (4kW peak) 1 output channel 4kW average (8kW peak)

VSWR: <1.2 : 1 (matched loads)

Weight: 17kg

Add to Quote

HFM2-20 – 2 x 20 kW HF Transmitter Multicouplers

Connectors: 3 1/8″ EIA

Cross Cover Frequency: Notch centre to be specified between 3-18MHz (lower notch centres available)

Environment: Outdoor unprotected -40°C to +55°C. Silicone oil cooled natural convection

Frequency: 0.1 – 32MHz

Impedance: 50 ohm

Insertion Loss: <0.3 dB (matched load)

Isolation: >30 dB (matched load)

Load VSWR: 3 : 1 max

Notch Width: 15%, 20%, 40% of cross over frequency

Power: 2 input channels each 20kW average (40kW peak) 1 output channel 40kW average (80kW peak)

VSWR: <1.2 : 1 (matched loads)

Weight: 325kg

Add to Quote

HFM2-5 – 2 x 5 kW HF Transmitter Multicouplers

Connectors: 7/8″, 1 5/8″ EIA, LC

Cross Cover Frequency: Notch centre to be specified between 3-18MHz (lower notch centres available)

Environment: Outdoor unprotected -40°C to +55°C. Silicone oil cooled natural convection

Frequency: 0.1 – 32MHz

Impedance: 50 ohm

Insertion Loss: <0.3 dB (matched load)

Isolation: >30 dB (matched load)

Load VSWR: 3 : 1 max

Notch Width: 15%, 20%, 40% of crossover frequency

Power: 2 input channels each 20kW average (40kW peak) 1 output channel 40kW average (80kW peak)

VSWR: <1.2 : 1 (matched loads)

Weight: 150kg

Add to Quote

MHFH2-RX-A

Balancing Loads: Internal

Configuration: Cast aluminium box, 0.05m x 0.05m x 0.03m solid encapsulation

Connectors: ‘N’ BNC

Frequency: 50kHz – 50MHz

Insertion Loss: <0.5 dB

Isolation: >35 dB

Power: 2 x 2 Watt

Temperature Range: -40°C to +55°C

VSWR: <1.2:1

Add to Quote

MHFH2-RX-B

Balancing Loads: Internal

Configuration: Cast aluminium box, 0.05m x 0.05m x 0.03m solid encapsulation

Connectors: ‘N’ BNC

Frequency: 10kHz – 32MHz

Insertion Loss: <0.5dB

Isolation: >35 dB

Power: 2 x 2 Watt

Temperature Range: -40°C to +55°C

VSWR: <1.2:1

Add to Quote

MHFH4-RX-A

Balancing Loads: Internal

Configuration: Cast aluminium box, 120mm x 60mm x 30mm solid encapsulation

Connectors: ‘N’ BNC

Frequency: 50kHz – 50MHz

Insertion Loss: <0.5 dB

Isolation: >30 dB

Power: 4 x 1 Watt

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1

Add to Quote

MHFH4-RX-B

Balancing Loads: Internal

Configuration: Cast aluminium box, 120mm x 60mm x 30mm solid encapsulation

Connectors: ‘N’ BNC

Frequency: 10kHz – 32MHz

Insertion Loss: <0.5 dB

Isolation: >30 dB

Power: 4 x 1 Watt

Temperature Range: -40°C to +55°C

VSWR: <1.2 : 1

Add to Quote

MSM16/4

Height Extended (m): 4.9

Height Retracted (m): 1.7

Number of Sections: 4

Vertical Head Load (kg): 22.67

Add to Quote

MSM20/4

Height Extended (m): 6.1

Height Retracted (m): 1.9

Number of Sections: 4

Vertical Head Load (kg): 22.67

Add to Quote

MSM25/6

Height Extended (m): 7.6

Height Retracted (m): 2.2

Number of Sections: 5

Vertical Head Load (kg): 22.67

Add to Quote

MSM30/6

Height Extended (m): 9.1

Height Retracted (m): 2.7

Number of Sections: 5

Vertical Head Load (kg): 22.67

Add to Quote

NH5

Height Extended (m): 5

Height Retracted (m): 1.41

Number of Sections: 5

Weight (kg): 15

Vertical Head Load (kg): 18

Add to Quote

NH7

Height Extended (m): 7

Height Retracted (m): 1.84

Number of Sections: 5

Weight (kg): 19

Vertical Head Load (kg): 15

Add to Quote

NH9

Height Extended (m): 9

Height Retracted (m): 2.3

Number of Sections: 5

Weight (kg): 23

Vertical Head Load (kg): 13

Add to Quote

NK11

Height Extended (m): 10.9

Height Retracted (m): 2.37

Number of Sections: 6

Weight (kg): 21

Vertical Head Load (kg): 18

Add to Quote

NK6

Height Extended (m): 5.9

Height Retracted (m): 1.64

Number of Sections: 5

Weight (kg): 26

Vertical Head Load (kg): 27

Add to Quote

NK9

Height Extended (m): 9

Height Retracted (m): 2.3

Number of Sections: 5

Weight (kg): 29

Vertical Head Load (kg): 22

Add to Quote

NL10

Height Extended (m): 10.5

Height Retracted (m): 2.5

Number of Sections: 6

Weight (kg): 41

Vertical Head Load (kg): 27

Add to Quote

NL12

Height Extended (m): 12.2

Height Retracted (m): 2.43

Number of Sections: 7

Weight (kg): 46

Vertical Head Load (kg): 25

Add to Quote

NL16

Height Extended (m): 15.6

Height Retracted (m): 4.15

Number of Sections: 5

Weight (kg): 61

Vertical Head Load (kg): 23

Add to Quote

NL22

Height Extended (m): 21.7

Height Retracted (m): 4.15

Number of Sections: 7

Weight (kg): 74

Vertical Head Load (kg): 14

Add to Quote

NL8

Height Extended (m): 7.9

Height Retracted (m): 1.77

Number of Sections: 7

Weight (kg): 34

Vertical Head Load (kg): 25

Add to Quote

NX10

Height Extended (m): 10.1

Height Retracted (m): 2.51

Number of Sections: 6

Weight (kg): 60

Vertical Head Load (kg): 50

Add to Quote

NX14

Height Extended (m): 13.6

Height Retracted (m): 2.64

Number of Sections: 8

Weight (kg): 70

Vertical Head Load (kg): 35

Add to Quote

NX18

Height Extended (m): 18.5

Height Retracted (m): 4.32

Number of Sections: 6

Weight (kg): 93

Vertical Head Load (kg): 30

Add to Quote

NX25

Height Extended (m): 25

Height Retracted (m): 4.44

Number of Sections: 8

Weight (kg): 110

Vertical Head Load (kg): 20

Add to Quote

NX30

Height Extended (m): 29.8

Height Retracted (m): 4.57

Number of Sections: 9

Weight (kg): 120

Vertical Head Load (kg): 14

Add to Quote

NX8

Height Extended (m): 7.6

Height Retracted (m): 1.91

Number of Sections: 7

Weight (kg): 50

Vertical Head Load (kg): 50

Add to Quote

NY9-7

Height Extended (m)
Height Retracted (m)
Number of Sections
Diameter of Top Section (mm)
Vertical Head Load (kgs)
Max Wind Speed Unguyed (kph)
Sail Area (m2)
Basic Weight of Mast (kgs)

Add to Quote

PA2 / B20 / 10

Height (m): 6.1

Weight (kg): 24

Add to Quote

PA2 / B24 / 6

Height (m): 7.32

Weight (kg): 23

Add to Quote

PA2 / B30 / 10

Height (m): 9.14

Weight (kg): 32

Add to Quote

PA2 / B30 / 6

Height (m): 9.14

Weight (kg): 29

Add to Quote

PA2 / B36 / 6

Height (m): 10.97

Weight (kg): 35

Add to Quote

PA2 / B40 / 10

Height (m): 12.19

Weight (kg): 40

Add to Quote

PA2 / B42 / 6

Height (m): 12.8

Weight (kg): 42

Add to Quote

PA2 / B48 / 6

Height (m): 14.63

Weight (kg): 48

Add to Quote

PA2 / B50 / 10

Height (m): 15.24

Weight (kg): 50

Add to Quote

PA2 / B60 / 10

Height (m): 18.29

Weight (kg): 55

Add to Quote

PA2 / B60 / 6

Height (m): 18.29

Weight (kg): 55

Add to Quote

PFC 12

Height Extended (m): 12.4

Height Retracted (m): 2.1

Add to Quote

PFC 5.8

Height Extended (m): 5.8

Height Retracted (m): 1.8

Add to Quote

PFC 7.5

Height Extended (m): 7.3

Height Retracted (m): 1.9

Add to Quote

PFC 9

Height Extended (m): 9

Height Retracted (m): 2

Add to Quote

Portable Dipole Antenna LW8 Series

Centre junction: Type SMC CCJ/2 moulding

Frequency Range: 3 – 30MHz or 2 – 30MHZ with ATU as a long wire antenna

Input Connector: BNC

Input Impedance: 50 ohm

Kit bag: Optional

LW8 / K: PVC covered kevlar braid with plaited copper wire

Metal Fittings: Stainless steel

Polarisation: Horizontal

Power Rating: Rx – 500W average

VSWR: 2 : 1 max at 50 ohm

Add to Quote

RL100-5 – 50 ohm 10kW Resistive Load

Frequency: 1.5 – 32MHz

Input Impedance: 50 ohm

Power: 10kW avg. continuous, 20kW peak

VSWR: <1.15 : 1

Connectors: 7/8″ or 1 5/8″ EIA

Weight: 60kg

Construction: Aluminium housing with Alocrom 1200 and enamel paint finish

Humidity: 100% at 30^°C

Temperature: -40^°C to +65^°C

Add to Quote

ST5-12

Height Extended (m): 12

Height Retracted (m): 2.9

Weight (kg): 29.5

Vertical Head Load (kg): 35

Add to Quote

ST5-15

Height Extended (m): 15

Height Retracted (m): 3.4

Weight (kg): 33.5

Vertical Head Load (kg): 35

Add to Quote

ST5-18

Height Extended (m): 18

Height Retracted (m): 3.9

Weight (kg): 37.5

Vertical Head Load (kg): 35

Add to Quote

ST5-6

Height Extended (m): 6

Height Retracted (m): 1.8

Weight (kg): 21

Vertical Head Load (kg): 35

Add to Quote

ST5-9

Height Extended (m): 9

Height Retracted (m): 2.3

Weight (kg): 25

Vertical Head Load (kg): 35

Add to Quote

SW2K

Frequency range: 3 to 30MHz
Bandwidth: +-2% of marker frequency
Power rating: 400W
Polarisation: Horizontal
Antenna elements: PVC coated braided copper Kevlar
Footprint: 24m
Input connector: M5 Fork Terminal

With markers. Kit bag not included.

Add to Quote

SW2K/MI

Frequency range: 3.5 to 30MHz
Bandwidth: Broadband with an ATU
Power rating: 400W
SWR: ATU required
Polarisation: Horizontal
Antenna elements: PVC coated braided copper Kevlar
Footprint: 20m
Input connector: M5 Fork Terminal

Add to Quote

SW2K/MI/CC

Add to Quote

SW2KAM

With markers and kit bag.

Add to Quote

SW2KM

Frequency range: 3 to 30MHz
Bandwidth: +-2% of marker frequency
Polarisation: Horizontal
Antenna elements: PVC coated braided copper Kevlar
Footprint: 24m
Input connector: M5 Fork Terminal

With more markers. Kit bag included.

Add to Quote

SWIFT10

Height Extended (m): 10

Height Retracted (m): 1.79

Number of Sections: 8

Weight (kg): 11.6

Vertical Head Load (kg): 8.5

Add to Quote

SWIFT10PN

Height Extended (m): 10

Height Retracted (m): 1.86

Number of Sections: 8

Weight (kg): 12.3

Vertical Head Load (kg): 8.5

Add to Quote

SWIFT4

Height Extended (m): 4

Height Retracted (m): 1.33

Number of Sections: 4

Weight (kg): 6.4

Vertical Head Load (kg): 10

Add to Quote

SWIFT4PN

Height Extended (m): 4

Height Retracted (m): 1.38

Number of Sections: 4

Weight (kg): 7

Vertical Head Load (kg): 10

Add to Quote

SWIFT5

Height Extended (m): 5

Height Retracted (m): 1.38

Number of Sections: 5

Weight (kg): 7.5

Vertical Head Load (kg): 10

Add to Quote

SWIFT5PN

Height Extended (m): 5

Height Retracted (m): 1.44

Number of Sections: 5

Weight (kg): 8.2

Vertical Head Load (kg): 10

Add to Quote

SWIFT6

Height Extended (m): 6

Height Retracted (m): 1.58

Number of Sections: 5

Weight (kg): 8.3

Vertical Head Load (kg): 10

Add to Quote

SWIFT6PN

Height Extended (m): 6

Height Retracted (m): 1.64

Number of Sections: 5

Weight (kg): 9

Vertical Head Load (kg): 10

Add to Quote

SWIFT7

Height Extended (m): 7

Height Retracted (m): 1.61

Number of Sections: 6

Weight (kg): 9.4

Vertical Head Load (kg): 10

Add to Quote

SWIFT7PN

Height Extended (m): 7

Height Retracted (m): 1.67

Number of Sections: 6

Weight (kg): 10

Vertical Head Load (kg): 10

Add to Quote

SWIFT8

Height Extended (m): 8

Height Retracted (m): 1.63

Number of Sections: 7

Weight (kg): 10.2

Vertical Head Load (kg): 10

Add to Quote

SWIFT8PN

Height Extended (m): 8

Height Retracted (m): 1.7

Number of Sections: 7

Weight (kg): 10.9

Vertical Head Load (kg): 10

Add to Quote

SWIFT9

Height Extended (m): 9

Height Retracted (m): 1.66

Number of Sections: 8

Weight (kg): 10.9

Vertical Head Load (kg): 8.5

Add to Quote

SWIFT9PN

Height Extended (m): 9

Height Retracted (m): 1.74

Number of Sections: 8

Weight (kg): 11.7

Vertical Head Load (kg): 8.5

Add to Quote

TA100-520

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 200 ohm

Add to Quote

TA100-530

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TA100-537

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TA100-545

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TA100-55

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TA100-560

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TA100-57

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TA100-580

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TA15-520

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TA15-530

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TA15-537

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TA15-545

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TA15-55

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TA15-560

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TA15-57

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TA15-580

AV Power: 150 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TA3/16/16/SS

Frequency range: 150 to 550KHz
Power rating: 10kW
SWR: ATU required
Polarisation: Vertical
Antenna elements: Three stainless steel
Antenna configuration: Tee
Footprint: 16m x 2m
Mast requirements: Two, 16m + height of the down link
Input connector: Wire

Add to Quote

TA3/22/16

Frequency range: 150 to 550KHz
Power rating: 10kW
SWR: ATU required
Polarisation: Vertical
Antenna elements: Three stainless steel
Antenna configuration: Tee
Footprint: 22m x 2m
Mast requirements: Two, 22m + height of the down link
Input connector: Wire

Add to Quote

TA3/30/15

Frequency range: 150 to 550KHz
Power rating: 10kW
SWR: ATU required
Polarisation: Vertical
Antenna elements: Three stainless steel
Antenna configuration: Tee
Footprint: 30m x 2m
Mast requirements: Two, 15m + height of the down link
Input connector: Wire

Add to Quote

TA3/70/35

Frequency range: 150 to 550KHz
Power rating: 10kW
SWR: ATU required
Polarisation: Vertical
Antenna elements: Three stainless steel
Antenna configuration: Tee
Footprint: 70m x 2m
Mast requirements: Two, 53m + height of the down link
Packed weight: 52kg
Input connector: Wire

Add to Quote

TA40-520

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 200 ohm

Add to Quote

TA40-530

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TA40-537

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TA40-545

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TA40-55

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TA40-560

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TA40-57

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TA40-580

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TA5-520

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 200 ohm

Add to Quote

TA5-530

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TA5-537

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TA5-545

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TA5-55

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TA5-560

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TA5-57

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TA5-580

AV Power: 50 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TAS100-520

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 200 ohm

Add to Quote

TAS100-530

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TAS100-537

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TAS100-545

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TAS100-55

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TAS100-560

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TAS100-57

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TAS100-580

AV Power: 1 kWi/ imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TAS40-520

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 200 ohm

Add to Quote

TAS40-530

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 300 ohm

Add to Quote

TAS40-537

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 370 ohm

Add to Quote

TAS40-545

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 450 ohm

Add to Quote

TAS40-55

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 50 ohm

Add to Quote

TAS40-560

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 600 ohm

Add to Quote

TAS40-57

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 75 ohm

Add to Quote

TAS40-580

AV Power: 400 Watt i/p imp: 50 ohm unbalance

Balance Impedance: 800 ohm

Add to Quote

TDLS/40

Frequency Range: 3-30MHz (60MHz with degraded performance)
Bandwidth: Broadband
Power Rating: 400W
SWR: 2.0:1
Polarisation: Horizontal
Gain: Up to 7dBi (Delta) at 12MHz
Antenna Elements: PVC coated Kevlar
Footprint: Delta Loop 55m, Dipole Dependent on configuration 72m at 2MHz / 5m at 30MHz
Mast Requirements: 9.9m Mast – not included
Input Connector: N Type
Cable: UR67 x 25m and UR67 x 15m
Packed weight: 32kg

Add to Quote

TDLS/400/SYS

Frequency Range: 3-30MHz (60MHz with degraded performance)
Bandwidth: Broadband
Power Rating: 400W
SWR: 2.0:1
Polarisation: Horizontal
Gain: Up to 7dBi (Delta) at 12MHz
Antenna Elements: PVC coated Kevlar
Footprint: Delta Loop 55m, Dipole Dependent on configuration 72m at 2MHz / 5m at 30MHz
Mast Requirements: 9.9m Mast included
Input Connector: N Type
Cable: UR67 x 25m and UR67 x 15m
Packed weight: 32kg

Add to Quote

TFD-150T

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 29m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N Type
Packed weight: 3.58kg
Cable: RG58 x 10m

Add to Quote

TFD-1KT

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 29m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N Type
Cable: RG58 x 10m

Add to Quote

TFD-400T

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 400W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 29m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N Type

Add to Quote

TFD/RTX-05BB/A

Frequency range: 5.5 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded copper wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 18.5m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Cable: UR67 x 30m PL259

Options: No coax

Add to Quote

TFD/RTX-05BB/B

Frequency range: 7.5 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 13.5m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Cable: UR67 x 30m PL259

Options: No coax

Add to Quote

TFD/RTX-05BB/C

Cable Assembly Included: Yes

Freq. Range (MHz): 10 – 30MHz

Nett Weight (kg) (Approx): 12

Overall Length (m): 10

Power Rating (PEP): 250W

Add to Quote

TFD/RTX-05BBE/A

Frequency range: 5.5 to 30MHz
Bandwidth: Broadband
Power rating: 250W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 18.5m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Packed weight: 6kg
Cable: Not included

Options: Coax

Add to Quote

TFD/RTX-05BBE/B

Frequency range: 7.5 to 30MHz
Bandwidth: Broadband
Power rating: 250W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded copper wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 13.5m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Packed weight: 6kg
Cable: Not included

Options: Coax

Add to Quote

TFD/RTX-05BBE/C

Frequency range: 10 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded copper wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 10m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Cable: UR67 x 30m PL259

Options: No coax

Add to Quote

TFDBB

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded copper wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 30m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector:SO239
Packed weight: 12kg
Cable: UR67 x 30m P259

Options: No coax

Add to Quote

TFDBB/1K/2MHz

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel stranded wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 38m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Cable: UR67 x 30m P259

Add to Quote

TFDBB/400

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 400W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel stranded wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 30m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Packed weight: 15kg
Cable: UR67 x 30m P259

Options: No coax

Add to Quote

TFDBB1K

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel stranded wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 30m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Packed weight: 24kg
Cable: UR67 x 30m P259

Add to Quote

TFDBBE

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 250W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Hard drawn stranded copper wire
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 30m excluding masts
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: SO239
Packed weight: 5kg
Cable: UR67 x 30m PL259

Options: No coax

Add to Quote

TPM10

Height Extended (m): 10

Height Retracted (m): 1.75

Vertical Head Load (kg): 8.5

Add to Quote

TPM12

Height Extended (m): 12

Height Retracted (m): 2.02

Vertical Head Load (kg): 7

Add to Quote

TPM8

Height Extended (m): 8

Height Retracted (m): 1.47

Vertical Head Load (kg): 10

Add to Quote

Trailer Mast – Up to 12m

Add to Quote

Trailer Mast – Up to 30m

Add to Quote

TWB2530/100

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 100W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated braided copper with Kevlar core
Antenna configuration: Inverted V
Footprint: 48m x 2.5m (22m mast stays)
Mast requirements: Single 11m
Input connector: N type
Cable: 20m x UR67 N type

Add to Quote

TWB2530/1K

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated braided copper with Kevlar core
Antenna configuration: Inverted V
Footprint: 48m x 2.5m (22m mast stays)
Mast requirements: Single 11m
Input connector: N type
Cable: 20m x UR67 N type

Add to Quote

TWB2530/400

Frequency range: 2.5 to 30MHz
Bandwidth: Broadband
Power rating: 400W
SWR: Better than 2.5:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated braided copper with Kevlar core
Antenna configuration: Inverted V
Footprint: 48m x 2.5m (22m mast stays)
Mast requirements: Single 11m
Input connector: N type
Cable: 20m x UR67 N type

Add to Quote

UL9-11

Height Extended (m): 10.34

Height Retracted (m): 2.32

Number of Sections: 7

Vertical Head Load (kg): 312+

Diameter of Top Section (cm): 15.2

Add to Quote

UL9-12

Height Extended (m): 11.60

Height Retracted (m): 2.37

Number of Sections: 8

Vertical Head Load (kg): 264+

Diameter of Top Section (cm): 14.0

Add to Quote

UL9-17

Height Extended (m): 17.61

Height Retracted (m): 4.22

Number of Sections: 5

Vertical Head Load (kg): 150+

Diameter of Top Section (cm): 17.8

Add to Quote

UL9-18

Height Extended (m): 18.80m

Height Retracted (m): 2.56

Number of Sections: 12

Vertical Head Load (kg): 90+

Diameter of Top Section (cm): 8.9

Add to Quote

UL9-21

Height Extended (m): 20.98

Height Retracted (m): 4.27

Number of Sections: 6

Vertical Head Load (kg): 140+

Diameter of Top Section (cm): 16.5

Add to Quote

UL9-24

Height Extended (m): 24.34

Height Retracted (m): 4.32

Number of Sections: 7

Vertical Head Load (kg): 90+

Diameter of Top Section (cm): 15.2

Add to Quote

UL9-31

Height Extended (m): 31.01

Height Retracted (m): 4.42

Number of Sections: 9

Vertical Head Load (kg): 40+

Diameter of Top Section (cm): 12.7

Add to Quote

UL9-4

Height Extended (m): 4.26

Height Retracted (m): 1.55

Number of Sections: 5

Vertical Head Load (kg): 420+

Daimeter of Top Section (cm): 17.8

Add to Quote

UL9-7

Height Extended (m): 6.32

Height Retracted (m): 1.7

Number of Sections: 8

Vertical Head Load (kg): 264+

Diameter of Top Section (cm): 14

Add to Quote

VDC 50/600 ohm Low Power Wide Band Measuring

Balance Impedance: 300 ohm to 600 ohm

Balance Ratio: See table below

Balanced Connection: M6 Insulators

Balanced Impedance: 600 ohm

Frequency Range: See table below

Insertion Loss: <0.2 dB

Power Rating: +10dBm

Temperature Range: -20°C to +55°C

Unbalanced Connection: See table below

Unbalanced Impedance: 50 ohm

VSWR: See table below

Add to Quote

WHISKEY-1K-ANT

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Inverted V
Footprint: 8.5m x 26.2m
Mast requirements: Single 9.1m
Input connector: N type
Packed weight: 18.6kg
Packed dimensions: 1020mm x 300mm x 230mm
Cable: URM67 20m

Add to Quote

WHISKEY-1K-ANT/C

Elements wound on winding spools. Small kit bag.

Add to Quote

WHISKEY-1K-ANT/EXT/A

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel
Antenna configuration: Inverted V
Footprint: 8.5m x 36m
Mast requirements: Single 9.1m
Input connector: N type
Packed dimensions: 1020mm x 300mm x 230mm
Cable: URM67 20m

Add to Quote

WHISKEY-1K-ANT/EXT/B

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Inverted V
Footprint: 8.5m x 36m
Mast requirements: Single 9.1m
Input connector: N type
Packed dimensions: 1020mm x 300mm x 230mm
Cable: URM67 20m

Add to Quote

WHISKEY-1K-ANT/SS

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 1kW
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel
Antenna configuration: Inverted V
Footprint: 8.5m x 26.2m
Mast requirements: Single 9.1m
Input connector: N type
Packed weight: 18.6kg
Packed dimensions: 1020mm x 300mm x 230mm
Cable: URM67 20m

Stainless steel elements

Add to Quote

WMPC

Frequency range: 3.5 to 30MHz with ATU
Bandwidth: Non resonant
Power rating: 150W
Polarisation: Vertical
Antenna elements: Single 2.4m fibreglass whip
Antenna configuration: Vertical
Footprint: 89mm Base 3 x M6 mounting screws
Input connector: M10 Stud
Cable: UR67 1.2m

Add to Quote

WMPCL

Frequency range: 2.5 to 30MHz with ATU
Bandwidth: Non resonant
Power rating: 150W
Polarisation: Vertical
Antenna elements: Single 3.5m fibreglass whip
Antenna configuration: Vertical or tied to bumper
Footprint: 89mm Base 3 x M6 mounting screws
Input connector: M10 Stud
Cable: UR67 1.2m

Add to Quote

Wolf 150

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 18m
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Packed weight: 2.5kg
Cable: RG58 x 10m N to BNC

Options:
– Counterpoise
– Sand colour wire
– Balun and Load Housing
– Rolatube mast 5m or 7m

Add to Quote

Wolf 150-ANT-90

Options:
– Counterpoise

Add to Quote

Wolf 150-ANT/CP/STST

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 150W
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: Stainless steel
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 18m
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Cable: RG58 x 10m N to BNC

Add to Quote

Wolf 400

Add to Quote

Wolf 400-ANT-90-CP-A

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 400W
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 28m
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Cable: RG58 x 10m N to BNC x 10m

Options:
– Counterpoise

Add to Quote

Wolf 400-ANT-FB

Frequency range: 2 to 30MHz
Bandwidth: Broadband
Power rating: 400W
SWR: Better than 1.8:1
Impedance: 50 Ohm
Polarisation: Horizontal
Antenna elements: PVC coated Kevlar
Antenna configuration: Horizontal, inverted V, sloping
Footprint: 18m
Mast requirements: One – Inverted and Slope; Two for Horizontal
Input connector: N type
Cable: RG58 x 10m N to BNC x 10m

Fixed base. Stainless steel.

Add to Quote

Wolf 400-ANT/CP/STST

Add to Quote

WTM Trailer Mast

Add to Quote

Related PRoducts

Adapters and Spigots

Our zinc-plated steel adapter is the perfect solution for supporting antennas horizontally or vertically, accommodating boom diameters of up to 1.5″. Whether you require stable antenna positioning or flexible orientation, this adapter delivers reliability and durability. Our team can tailor spigots to suit your unique requirements, ensuring seamless integration and optimal performance.

Add to Quote

Base Guy Assembly

Our Base Guy Assembly is ideal for extending masts on open ground. Complete kit includes mast fittings, 3 guys, adjusters, base plate, ground stakes, and pegs. Available in polyester or galvanized wire guy ropes, depending on the mast series. Quick and easy to set up, providing vertical mast support.

Add to Quote

Cable Guide

Made of stainless steel, the SMC Cable Guides are essential for securely attaching feeder cables of up to 0.47″ diameter to the mast without disconnecting end terminations. Screw into specially provided tapped holes in each mast collar. Sold individually.

Add to Quote

Climbing Steps

Enhance your field applications with SMC’s Climbing Steps. Our Climbing Steps are invaluable accessories that offer easy access to locking collars and antennas during field operations. These mast climbing steps are designed to clamp onto any position of the mast’s lower section and can be conveniently folded upright for transit. They are designed to provide safe and secure access and are typically used by technicians or maintenance workers who need to ascend or descend masts for various purposes, such as inspection, maintenance, or installation of equipment. Safety precautions, including the use of appropriate personal protective equipment (PPE) such as harnesses and helmets, are crucial when working at heights. Always follow manufacturer guidelines and industry safety standards when using mast climbing steps or any other equipment for working at elevated heights. We offer single steps for climbing and double steps for resting, ensuring your safety and convenience during mast operations.

Add to Quote

Field Stand

Designed for field extension of NK-Series masts, the SMC Field Stand features a four-legged aluminium alloy construction with adjustable legs for uneven terrain. Foldable legs for convenient transit and ground pegs for anchoring. Top bearing permits mast rotation, and a thumbscrew locks it in desired azimuth. Note: Top guys required at specified wind speeds for NK-6, NK-9, and NK-11 masts.

Add to Quote

Foot Pump

The NFP/1 Foot Pump offers ease of use, allowing you to raise your mast with ease and convenience. The speed and ease of extension depend on the user’s abilities and the volume of air needed to raise the mast. Whether you’re using it for recreational purposes, professional applications, or emergency situations, the NFP/1 Foot Pump ensures a reliable and straightforward mast extension process.

Add to Quote

HD SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

Kilfrost

Don’t let harsh winter elements compromise your mast performance of your SMC masts. Kilfrost is the ultimate cold-weather lubricant specially formulated to keep your SMC masts operating smoothly and efficiently even in the most extreme cold temperatures, where freezing is a possibility. When winter sets in, it’s crucial to ensure your SMC masts are prepared to face freezing conditions. This is the perfect solution for winterizing your masts, offering a unique lubricant formula tailored to combat the challenges posed by cold environments. To protect your SMC masts from potential damage and seizing issues, download our complimentary guide to discover more about maintaining your mast here.

Add to Quote

Lightning Protection Kit

Designed with precision and engineering excellence, the Hilomast Lightning Protection Kit seamlessly integrates with a series of masts, accommodating heights ranging from 16.4′ up to an impressive 98.4′ (5m up to 30m). Whether you have a small-scale installation or a towering mast system, rest assured that our lightning protection kit is tailored to suit your needs. Ensure the safety and longevity of your valuable masts and mast systems with the Hilomast Lightning Protection Kit. We understand the importance of safeguarding your investments from the unpredictable forces of nature, and our lightning protection kit is the ideal solution for providing a reliable defense against harmful weather conditions. The safety of your masts is of utmost importance to us, which is why we offer this specialized kit as an extra layer of protection for both new and pre-existing masts and mast systems. Our lightning protection kit offers peace of mind, knowing that your equipment is shielded from lightning strikes and other harsh weather-induced damage. Don’t take chances when it comes to safeguarding your assets. Trust the Hilomast Lightning Protection Kit to shield your masts and mast systems, ensuring their continued performance and durability even in the face of nature’s fiercest elements. Invest in proactive protection and elevate your mast’s resilience with Hilomast.

Add to Quote

Magnetic Safety Switch

Simple yet effective, the Magnetic Safety Switch is conveniently fitted to the outer tube of the mast and operated by a set of magnets positioned at the bottom of the inner mast tube. These magnets are securely bonded into an aluminum housing, which can be effortlessly inserted into the top section of the mast without requiring any dismantling. Inserting the magnet housing is a breeze – just remove the plastic end-cap of the top section and insert the housing. The neoprene ‘O’ ring automatically retains it in position, providing a secure fit.

Add to Quote

Mast Cover

SMC’s tailor-made mast covers are the perfect solution for safeguarding your mast from dust, dirt, rain, and other environmental factors during periods of non-use. Crafted from robust, waterproof materials, these custom covers are designed to snugly fit over mast collars and securely fasten to the mast using a practical strap. Choose from our end cover or full mast cover options, both meticulously tailored to offer optimal weather protection. With a diverse range of mast sizes available, you’ll find the ideal mast cover for every SMC mast in our collection.

Add to Quote

NH SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

NK SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

NL SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

NX SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

NX25M SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

Nycoil

Nycoil, a specialized tubing, serves as a protective sheath, ensuring that wires and cables are neatly arranged and secured during mast operations.

To meet specific requirements associated with this accessory, we highly recommend reaching out to us before making your Nycoil selections. Our team will provide expert guidance to ensure the perfect fit for your needs.

For masts requiring electrical wiring to the masthead, SMC strongly recommends using Nycoil for optimal wire management. Nycoil is available in standard black or red and comes in the following sizes: 1 1/4″ 1″ 3/4″ At SMC, we offer quotes for Nycoil both with and without wire, tailored to your exact specifications. Our customer support team is ready to assist you with any inquiries and provide personalized quotes. Simply reach out to us using the contact form below for prompt assistance. Experience the efficiency and reliability of the SMC Nycoil Wire Management System – ensuring a seamless and secure setup for your mast wiring needs.

Add to Quote

Plug-n-Go Compressor

Our Plug-n-Go Compressors are your ultimate choice for reliable, versatile, and easy-to-use air compressors, available in two power options: 12V DC or 115V AC. With a user-friendly design, these compressors feature a regulator, a pressure cut-off switch, an electronic dump valve, and a psi gauge, ensuring straightforward operation and precise control. Their compact size and portable nature make them perfect for on-the-road use, particularly in broadcast vehicles. Safety is paramount with the electronic quick dump safety exhaust, offering swift and secure mast retraction. Enclosed in a rugged and water-resistant case with a convenient handle, the SMC Plug-n-Go Compressor is built to withstand demanding conditions. Choose from optional colors, such as camouflage, black, or tan, based on availability, to match your preferences. Rest assured, all SMC Plug-n-Go Compressors are CE & UL rated, meeting high standards of safety and performance. Experience the convenience and reliability of the SMC Plug-n-Go Compressors – your go-to solution for a wide range of applications, both on and off the road.

Add to Quote

Portable Tilt-Over System

The SMC Portable Tilt-Over (PTO) System is a reliable, compact, and self-contained solution for on-the-move camera surveillance and security systems. Designed to deliver exceptional performance, this robust unit boasts a bed-mountable design, perfectly fitting standard pickup truck beds for effortless transportation and deployment. Key Features of the SMC Portable Tilt-Over (PTO) System: 1. Equipped with a 12v Deep Cell Battery, ensuring uninterrupted power supply during operations. 2. Boasts a 330lbs Capacity Actuator, providing sturdy support for your surveillance equipment. 3. Includes the SMC Storm Composite (ST) Series Belt-Driven Mast, offering a variable height range between 16′ to 33′ (5-10 meters), allowing for optimal positioning and coverage. 4. Designed to accommodate Nycoil (customer-supplied wire), providing flexibility to suit your specific requirements. Experience the convenience and versatility of the SMC Portable Tilt-Over (PTO) System – a compact powerhouse for your mobile camera surveillance and security needs. Effortlessly capture every angle and keep a watchful eye on the move with this reliable and easy-to-use unit.

Add to Quote

Rapid Deployment Unit (RDU)

Experience swift and effortless mast assembly with our RDU, designed to get your telescopic mast extended within minutes. Built to meet stringent MIL-SPEC 810.E standards, this rugged unit provides a sturdy base for your mast, ensuring reliability even in challenging conditions. This Rapid Deployment Unit is designed to fit almost any vehicles including 4x4s and SUVs, providing a seamless integration with your vehicle. Utilising your vehicle’s weight, the RDU securely holds the foot of the base in place without the need for complicated installations. Need a customised solution? No problem! Special attachment brackets can be tailor-made to suit your specific requirements. Achieve precise aerial or lighting direction with the unique swivel base feature, enabling easy adjustments for optimal performance. Versatility is a key highlight, as the Hilomast RDU kit can be placed under any wheel of your vehicle, ensuring convenience and adaptability. Reach impressive heights of up to 39ft, dependent on your head-load requirements, with our RDU kit. Whether you’re on a critical mission, broadcasting, or conducting surveillance, trust in SMC’s Rapid Deployment Unit to provide rapid and reliable mast deployment.

Add to Quote

Reese Hitch Mount

With the Reese Hitch Mount, you gain the freedom to take your mast systems virtually anywhere, as long as there is sufficient space for safe and reliable deployment. Designed with a focus on sturdiness and ruggedness, the Reese Hitch Mount guarantees optimal mast stability, ensuring your equipment remains secure during use. Experience unparalleled convenience and versatility with the SMC Reese Hitch Mount – your key to effortless mast deployment on the go.

Add to Quote

RES/30/48/2

Centre plate: 600 x 600mm Radials: 30 x 48m Copper 7 x 0.82

Add to Quote

RES/36/15/1

Centre plate: 300 x 600mm Radials: 30 x 15m Copper 7 x 0.82

Add to Quote

RES/36/15/2

Centre plate: 600 x 600mm Radials: 36 x 15m Copper 7 x 0.82

Add to Quote

RES/36/20/2

Centre plate: 600 x 600mm Radials: 36 x 20m Copper 7 x 0.82

Add to Quote

RES/36/30/1

Centre plate: 300 x 300mm Radials: 36 x 30m Copper 7 x 0.82

Add to Quote

RES/36/30/2

Centre plate: 600 x 600mm Radials: 36 x 30m Copper 7 x 0.82

Add to Quote

RES/36/35/1

Centre plate: 300 x 300mm Radials: 36 x 35m Copper 7 x 0.82

Add to Quote

RES/36/45/1

Centre plate: 300 x 300mm Radials: 36 x 45m Copper 7 x 0.82

Add to Quote

RES/48/30/2

Centre plate: 600 x 600mm Radials: 48 x 30m Copper 7 x 0.82

Add to Quote

RES/50/30/1

Centre plate: 300 x 300mm Radials: 50 x 30m Copper 7 x 0.82

Add to Quote

RES/50/45/1

Centre plate: 600 x 600mm Radials: 50 x 45m Copper 7 x 0.82

Add to Quote

RES/RM/SP

Centre plate: 1000 x 1120mm Radials: 8 x 6m Copper 7 x 0.82

Add to Quote

Rotation Handle

The SMC Rotation Handle is an accessory designed to simplify mast rotation. It effortlessly aids in the smooth rotation and adjustment of the position of your SMC mast to optimise the orientation of antennas for better signal reception or transmission. It conveniently folds to a vertical position when not in use. Installation is a breeze, as these handles can be easily fitted after mast installation.

Add to Quote

Side Mounting Brackets

Add to Quote

SuperFluid

This specialised fluid ensures optimal performance and longevity for your pneumatic masts, making it an essential component of your mast maintenance routine. Recommended for all SMC and Hilomast masts, this SuperFluid formulation is specifically tailored to meet the exacting requirements of our pneumatic masts, ensuring smooth operation and preventing any potential seizing issues. Maintaining your pneumatic masts has never been easier – we highly recommend incorporating SuperFluid into your regular maintenance regimen. By doing so, you safeguard your masts against wear and tear, enhancing their durability and ensuring they remain in top-notch condition for years to come. Don’t compromise on the performance and lifespan of your pneumatic mast. With proper application, you can rest assured that your pneumatic mast will operate flawlessly, standing tall and strong even in the most challenging conditions. Our self-service spares kits also include lubrication fluid.

Add to Quote

SWIFT SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

Top Guy Assembly

For enhanced stability in inclement weather, the SMC Top Guy Assembly includes an aluminium guy collar, D shackles, and 3 paracord guys with rope grips and nylon adjusters. Designed to clamp to the upper end of the second from the top mast section. Provides additional support during high wind speeds.

Add to Quote

Tripod Stand

The SMC Tripod Stand offers reliable free-standing support for NH-Series masts on hard surfaces. Made from sturdy steel, it folds into a compact unit for easy storage and transit. With adjustable feet for uneven ground, the mast can be rotated and locked in any position. Recommended for light winds and requires top guys in windy conditions. Weight: 16.8kg. Leg radius: 4.2ft.

Add to Quote

Tripod System

Our Tripod System is purpose-built to seamlessly handle a wide range of our N-Series and TPM Series masts, offering unmatched adaptability and ease of use. Whether you need to deploy a shorter mast like the NH-5 or a larger one like the NK-9, this adjustable tripod system delivers utmost convenience and efficiency. Designed with stability in mind, the tripod features adjustable outriggers, ensuring rock-solid support and enhanced safety. Deploy your mast on uneven terrain with confidence, as the outriggers guarantee a level and secure setup. Engineered in-house to perfectly complement our mast systems, this Tripod System provides a reliable and durable solution for various applications. Trust in the exceptional quality and performance of our products, tailored to meet your specific needs.

Add to Quote

UL9 SERVICEKIT

Includes complete set of dampers, PTFE, pan head, retaining screws, keyway guides, complete set of seals, Sample of high quality Super Fluid lubricant and winter Kilfrost.

Add to Quote

Upright Mount

Engineered with precision and constructed from high-quality steel, this rigid stand is designed to complement all masts up to a 6″ base, providing unparalleled stability and reliability. Versatility is at the core of the Hilomast tilt Mount system. Thanks to its innovative design, the stand can be easily disassembled, making storage and transportation a breeze. Whether you need to move it to a different location or simply stow it away when not in use, the Hilomast Upright Mount has you covered. Say goodbye to complicated installations and enjoy the convenience of a freestanding system. No need for additional support structures or permanent fixtures; the Hilomast Upright Stand is sturdy enough to stand on its own, saving you time and effort during setup. But that’s not all – we’ve taken it a step further! The Hilomast Upright Stand is also fully compatible with trailer systems, granting you the flexibility to bring your mast anywhere the road takes you. Experience unmatched portability and convenience like never before. Whether you’re a professional in need of a reliable mast support system or an outdoor enthusiast looking for a versatile solution, the Hilomast Upright Mount is the answer. Trust in its durability, embrace its adaptability, and elevate your mast experience to new heights.

Add to Quote

Vehicle Roof Bearings

SMC’s Vehicle Roof Bearings are essential accessories for securely mounting masts through the roof of your vehicle. The assembly consists of an upper and lower aluminium bearing, designed to ensure stability and ease of use. The upper bearing comprises three separate components: a flange with a Teflon ring, securely bolted to the vehicle’s outer skin, a tapping plate, and a weatherproof shield that clamps firmly onto the mast. This design guarantees a reliable and weather-resistant setup. The lower bearing base plate features a Teflon disc, allowing effortless rotation of your mast, and a thumb screw for locking it into position. For our NX Series masts, an optional locking collar is available. The base plate is securely bolted to the vehicle floor using four M12 bolts spaced on a 5.5″ P.C.Dia.

Add to Quote